Finally got the last of the 2020 Harry Potter sets. I ordered it back in December 2020, it was out of stock, it showed up, it shipped, USPS “lost it,” I’m working with LEGO on a replacement, and I reordered to have to wait for it to come off back order to actually get it. So let’s hope it’s worth it…
Released back on 3 July 2020, #75980-1 contains 1047 pieces and retails at $99.99. This works out to $0.096 per piece. Not too bad, but I have yet to see this set on sale (even in Germany). Onto the review…
The box shows both sides of the set on the front with some designed features. The back shows all of the different play features like most sets do.
The set contains seven numbered parts bags, an un-numbered bag with larger plates, and the instructions are sealed up with the stickers.
Here are the instructions and stickers. Nothing special about the instructions. No special write ups or pictures. There are two sticker sheets which are both fairly small. One is the normal sheet and the other is clear stickers. There aren’t a ton of stickers so I can’t complain too much. As a technique, I’ve started using the piece separator to apply stickers versus my fingers. It’s actually worked very well. Maybe you all already do that, but if you haven’t, give it a try.
The first bag contains a piece separator and starts the base of the building. It is connected with hinges so you can get to the inside later on which works out nice for play features. You get a pig with this set… I didn’t even know they had pigs, but I won’t complain. You also get Arthur and Molly Weasley.
For the rest of the build, I decided not to include the minifigs by bag and I’ll bring them all up at the end.
The second bag of parts builds out the living space. You get a table loaded up with a breakfast of eggs and waffles. There’s a small little sink area as well. The living space has a couch, a chair, and various decorations to include lamps, candles, and plants. Outside, you can see some of the clear stickers which actually look pretty decent. I managed to put them on without getting any air bubbles in them so that was good.
The third bag finishes up the inside of the first floor and starts on the roof. Inside, you can see the fireplace where they enter the floo network. The fireplace is connected to a Technic axle that you can spin between flames and the floo network green. I show it in translucent green here and then in the translucent orange below.
Here’s the orange, “normal” fire place. On the other side of the fire place, you see a clock which shows where everyone in the family is located. There’s also a picture on the wall and a book shelf.
Bag four finishes up the roof on the ground floor and adds a room on the second floor. I assume it is Ginny’s room with the hair brush and mirror. The bed has multiple colors and then a sticker that matches the colors. It was tricky to line up the sticker with the parts, but I think I got it close to being right. The downside to this set up is the sticker is smaller than the tile it goes on so there is a gap between the sticker and the sloped bricks which from far away isn’t a big deal, but close up looks bad.
The fifth bag starts the next level. This eventually becomes Arthur and Molly Weasley’s room. For now, there is a chair with some magical knitting going on at it. There’s also a family picture on the wall.
The sixth bag puts a bed in Molly and Arthur’s room with a quilt on it. It also adds in a room above. Maybe Ron’s room? There’s a bed and a picture on the wall, but that’s it. From the room, there’s a small stair way that leads up to a small upper porch area. That area has a broom so you can either sweep it off or fly away from there.
The last bag finishes the roof and adds a chimney. You also get two owls to include Hedwig. The roof is made with 45 degree slopes, but they vary in color so it adds to the design other than just using one color. I’ll cover the last part of this build with the minifigures.
The set comes with eight minifigures. Seven of them are unique to this set and then #8, Harry Potter, also comes in #75967-1: Forbidden Forest Umbridge’s Encounter. As mentioned in the bag seven section, it includes more besides the roof. It also includes a section of flames as can be seen in the sixth movie. The two minifigures included in bag seven are Bellatrix Lestrange and Fenrir Greyback. They both come with wands.
The remaining six as shown in the picture are Nymphadora Tonks, Ron Weasley, Ginny Weasley, Harry Potter, Molly Weasley, and Arthur Weasley. They all come with wands as well.
I think this is a pretty good mix for the set and you get a decent amount. For minifigure collectors, you get seven unique Harry Potter minifigures so not bad.
Here’s the final set. I like how they created the offset angle of the upper level. My Non-LEGO Spouse originally saw it and thought I didn’t connect everything. I had to explain that it was built that way. A nice touch.
Overall a good set that closely follows the Harry Potter version from the movie at an age 9+ range with just over 1,000 pieces. There are some good building techniques, but nothing overly challenging. For MOC builders you get some good pieces to pick from for your own builds. Price wise it is not bad, but it could be cheaper. I didn’t find it on sale, but I did get it with a freebie so that helped. If you wait a bit longer, you might be able to pick it up on sale. Just don’t wait too long and have it retire.
And that closes out the 2020 Harry Potter line for me. What are your thoughts on this set?
Happy building!
